We have tested both the Aiper Scuba X1 and the Beatbot AquaSense 2 Pro in real pools, measured their suction at the intake, and lived with the filtration and daily routine each one requires. This comparison brings those results together so you can see the real-world trade-offs without relying on the numbers printed on either box.
Both use cordless power, so this matchup turns on measured pull, filtration, coverage, automation, and value.
The short answer: we recommend skipping both. Neither robot earned a buy call in our pool testing. If you want our closest recommended alternative for what you are shopping here, look at the Dolphin Sigma (2.0 PSI). If you are strictly choosing between these two models, the Beatbot AquaSense 2 Pro is the lesser compromise (pulling 1.5 vs 1.2 PSI on our gauge).
Quick Answer
Our honest call is to skip both robots and buy the Dolphin Sigma instead. Closest smart-flagship alternative: boosts suction from 1.2–1.5 PSI to 2.0 PSI across a 10-inch dual intake, includes top-load pleated NanoFilters, and keeps full underwater Wi-Fi app control with a 3-year warranty. If your priorities lean more toward smaller pools that need set-and-forget cleaning on a sensible budget, also look at the Dolphin Cayman (1.5 PSI).
If you are already committed to one of these two, Beatbot AquaSense 2 Pro takes the narrow edge (pulling 1.5 vs 1.2 PSI on our gauge). The Aiper Scuba X1 is only worth considering for buyers committed to the X1 design who want the lowest entry price.
Our calls in the full reviews are Not recommended for the Aiper Scuba X1 and Not recommended for the Beatbot AquaSense 2 Pro. Those calls matter here: PSI is the first round, not the entire verdict.
Suction Power: 1.2 PSI vs 1.5 PSI
On our hydro manometer, the Aiper Scuba X1 measured 1.2 PSI and the Beatbot AquaSense 2 Pro measured 1.5 PSI. That gives the Beatbot AquaSense 2 Pro a 0.3 PSI advantage, or about 25% more intake pressure than the lower reading.
We measure pressure directly at the intake with the same gauge and pool setup. That is different from manufacturer flow-rate claims in gallons per hour: GPH describes water movement, while PSI shows how hard the intake pulls on debris. Cordless results are recorded at full charge. Our complete pool-robot suction test explains the method and shows where both robots sit on the full board.
The number needs context. It is easy to set up, looks polished, and beats the X1 Pro on canonical measured suction. It offers a polished dock, useful modes, and a respectable 1.5 PSI at full charge. The stronger gauge result gets this round, though intake pressure alone cannot make up for a filter that lets fine debris escape or a routine that makes you handle the robot every day.
Filtration and Debris Handling
The Aiper Scuba X1 uses basic mesh basket. The Beatbot AquaSense 2 Pro uses dual-layer flat mesh basket.
We give the filtration edge to the Beatbot AquaSense 2 Pro. Our comparison favors fine-particle capture, usable debris capacity, easy cleaning, and whether the better filter is included rather than sold as an upgrade.
For leaves, capacity and intake design matter. For pollen, silt, and the haze that dulls otherwise clear water, the filter media matters more. A basic mesh screen can look clean after a run while still passing the smallest material back into the pool.
Automation and Daily Work
The Aiper Scuba X1 is cordless. Simple app setup, but the connection drops underwater and charging is daily. The Beatbot AquaSense 2 Pro is cordless. App features and a wireless dock, but still needs daily retrieval and charging.
Because both are cordless, neither is truly set-and-forget. Compare runtime and app features, but plan on retrieving, charging, and redeploying either robot between cycles.
We score automation as a tie.
Coverage and Pool Fit
For the Aiper Scuba X1, our review found floor, walls, and waterline in cordless cycles. The Beatbot AquaSense 2 Pro is built for floor, walls, and expanded cordless cleaning modes.
Coverage is a tie in our scoring, so choose around pool size, shape, and the surfaces you actually need cleaned.
Surface coverage on a spec sheet only goes so far if suction fades or the filter misses fine dust. Match the robot’s reach to your pool size, and weigh how often you are willing to handle the unit to keep those surfaces clean.
Value: Performance for the Money and Time
Our value take on the Aiper Scuba X1: The least costly X1, though stronger corded cleaners remain the better use of the budget. For the Beatbot AquaSense 2 Pro: A large price jump over the base model without stronger measured suction.
The value edge goes to the Aiper Scuba X1.
Value is not the same thing as the lowest checkout price. We count cleaning power, filtration, how many surfaces the robot covers, and how often you have to retrieve or charge it. A cheaper robot that leaves you vacuuming behind it is not a bargain, and an expensive robot only earns its price when its extra capability solves a real problem in your pool.
What to Buy Instead
Because both the Aiper Scuba X1 and Beatbot AquaSense 2 Pro earned a skip in our testing, compare them directly against any pick from our Best Robotic Pool Cleaners of 2026 list below — starting with our closest match, the Dolphin Sigma:
| Category | Scuba X1 | AquaSense 2 Pro | Sigma (Buy Instead) |
|---|---|---|---|
| Our review call | Skip | Skip | Recommended |
| Measured suction | 1.2 PSI (full charge) | 1.5 PSI (full charge) | 2.0 PSI (constant corded) |
| Filtration | Basic mesh basket | Dual-layer flat mesh basket | Top-loading pleated NanoFilter cartridges for fine dust, pollen, and silt |
| Automation | Simple app setup, but the connection drops underwater and charging is daily | App features and a wireless dock, but still needs daily retrieval and charging | MyDolphin Plus app works underwater and supports weekly scheduling |
Closest smart-flagship alternative: boosts suction from 1.2–1.5 PSI to 2.0 PSI across a 10-inch dual intake, includes top-load pleated NanoFilters, and keeps full underwater Wi-Fi app control with a 3-year warranty.
You can also read our direct head-to-head breakdowns for Aiper Scuba X1 vs Dolphin Sigma and Beatbot AquaSense 2 Pro vs Dolphin Sigma, or look at the Dolphin Cayman (1.5 PSI) if your pool leans more toward smaller pools that need set-and-forget cleaning on a sensible budget.
If You Still Pick Between These Two
- Lesser compromise — Beatbot AquaSense 2 Pro: Takes the head-to-head edge (pulling 1.5 vs 1.2 PSI on our gauge). It offers a polished dock, useful modes, and a respectable 1.5 PSI at full charge.
- Narrow case for Aiper Scuba X1: Only relevant for buyers committed to the X1 design who want the lowest entry price. It is easy to set up, looks polished, and beats the X1 Pro on canonical measured suction.
- Why we skip both overall: Beatbot AquaSense 2 Pro — It costs far more than the base AquaSense 2 while testing slightly lower on suction. Aiper Scuba X1 — Its 1.2 PSI, basic filter, underwater app disconnect, and recharge routine limit the value.
Final Verdict
Skip both — buy the Dolphin Sigma instead. Beatbot AquaSense 2 Pro edges out Aiper Scuba X1 in a forced comparison (pulling 1.5 vs 1.2 PSI on our gauge), but both carry a Not recommended call in our reviews. The Dolphin Sigma (2.0 PSI) is the closest recommended robot to buy instead.
Read the complete Aiper Scuba X1 review and Beatbot AquaSense 2 Pro review for every test photo, setup detail, and long-form ownership note. You can also return to all pool-robot comparisons to see any other matchup from the 19 cleaners in our test set.
